home *** CD-ROM | disk | FTP | other *** search
/ Tech Arsenal 1 / Tech Arsenal (Arsenal Computer).ISO / tek-20 / mods_all.zip / TH215.3 < prev    next >
Text File  |  1992-09-15  |  3KB  |  64 lines

  1. TH215.3
  2.  
  3. Date: 05 May 90 13:41:36 UTC (Sat)
  4. From: wa2ise@kd6th.nj.usa (Bob)
  5. Message-ID: <25694@KD6TH.NJ.USA>
  6. Subject: a TH215 no audio fix
  7.  
  8.  
  9. Newsgroups: rec.ham-radio
  10. Subject: Re: Kenwood TH-215A no audio problem
  11. Organization: Hewlett-Packard Co., Corvallis, OR, USA
  12.  
  13. PROBLEM:
  14. >In a sample population of about 60 amateurs in this town, three of us
  15. >own Kenwood TH-215A HT's, all purchased separately at different times
  16. >from different sources....
  17.  
  18. >ALL THREE have developed an audio problem in the last eight months:
  19. >the audio (both from the microphone and from the keypad) simply
  20. >disappears at unpredictable intervals.  And all three can be "fixed"
  21. >by WHACKING the HT with the palm of one's hand--until it happens again.
  22.  
  23. A POSSIBLE FIX:
  24.  You guys may be in luck, since I fixed mine -- I have the service manual
  25. and decided to jump in (I had upgraded the software and you have to pull the
  26. unit completely open to do it -- ). Anyway, I was using the rig one day and
  27. the next -- no audio -- just a slight noise that appeared to be white noise
  28. from the final audio buffer. When plugging in the speaker mike -- same
  29. problem. Touch the TTPAD and get your ears blown away -- I think beep also
  30. worked. Kenwood had no knowledge of previous problems.
  31.  
  32. I had to rig-up a jumper ribbon cable so I could lay the rig out for
  33. testing and immediately checked the input audio to the volume control.
  34. No problem -- but there was nothing coming out the other side. I
  35. jumpered the pot (i.e. simulate pot max volume) and my ears were
  36. hurting. Upon removal of the pot I found a crack on the ALPS pc board
  37. that has the leads mounted to it. Apparently, I must have hit the
  38. volume control pot the previous day and cracked the pot trace (again
  39. this trace was part of the pot not the rig pcb). I had noticed when I
  40. disassembled the unit that there was no nut on the pot to hold it in
  41. place (none on the squelch either). The volume pot is right at the edge
  42. of the unit and is the most likely knob to get hit.
  43.  
  44. When parts arrived, it came with a nut so I installed it to help prevent
  45. this problem in the future -- no problems since.
  46.  
  47. I think the switched volume pot cost $4.95 + $3.00 shipping.
  48.  I also picked up a set of backcase screws -- very small
  49. heads but very long screws to replace my old ones -$.05 - Make sure you have a
  50. "good" screwdriver that really fits.)
  51.  
  52. All these problems sound like the same thing. I have never had any problems
  53. with my rig, and I bought one of the first ones out. (Hence, the software
  54. update to give me the ability to lock out memory channels during scan.)
  55.  
  56. Hope this helps.
  57.  
  58. Greg May
  59. gregm@hp-pcd.HP.COM
  60.  
  61. Note: I haven't tried or verified this, proceed at your own risk! WA2ISE
  62.  
  63. %
  64.